The Event: RACE WARS
Date: OCTOBER 24th, 2026
Locations: DER SLOTTENHAUSEN 1 RACE
BJM SLOTCARS 1 RACE
BOLINGBROOK SPEEDWAY 2 RACES (tentatively)
The Cars: HYPERCARS

HELIGIBLE CARS:
Scaleauto, Cadillac LMH, BMW Hybrid GTP, Peugeot 9x8 LMH, Porsche P-963 GTP, and Lamborghini. Other hypercars will be allowed as produced.

SLOT.IT CA56 ACURA ARX-05, CA63 Toyota Gr010

Scalextric SCA-C4515, or C4512 Cadillac.

NSR Generic Hypercar

BODY:
Must not be modified or cut in any way

Must be completely painted in a realistic racing livery if not pre-decorated. White kit bodies must have at least a coat of paint on them no naked bodies.

Must start each race with all parts intact except for mirrors, antennas and similar small protruding parts.

Rear wing may be taped or glued in place. Rear wing does not need to be replaced if it comes off durir the race but must be replaced by the next race in the proper position.

Windows must be transparent with the exception of tampo paint or decal headers.

Body screws may be run loose.

ANY brand body to chassis screw is permitted but only in stock location.

Body must have a number (the same number...) in at least three (3) locations.

INTERIORS:
Fully stock, painted

Interior may be modified to allow proper clearance for the motor if necessary.

CHASSIS:
Only stock NSR, Scaleauto, Slot.it, or Scalextric chassis main plates, motor pods are allowed.

Only the stock motor pods are allowed.

Only minor flash removal is allowed on the chassis and motor pod.

No modifications to the axle or bushing mounts are permitted.

Bushings may be glued in place.

The use of tape on the chassis to hold the motor pod in place is approved.

Any Scaleauto or NSR brand motor pod to chassis screws may be used but only in stock locations.

Ballast may be used, ONLY Lead or Tungsten are allowed. Ballast must not offer any support to the chassis or motor pod. Ballast may be placed on the underside of the chassis but care should be used not to contact the track

Any brand axles may be used.

You are allowed to use any combination of glue, tape or screws to secure your motor to the motor pod.

EXCEPTIONS:
Any Brand of Adjustable Front Axle Ride Height screws may be used.

MAGNETIC DOWNFORCE:
No magnets are allowed, you must remove the stock magnet if the car came with one.

WHEELS AND TIRES
FRONT TIRES: Only stock front tires may be used or Quick Slicks Zero grips. Front tires
may be glued and trued (diameter only) with no visual evidence of significant front tire taper allowed. Front tires
may be coated in CA Glue, Nail Polish or Acrylic Floor Wax.

TIRE/WHEEL POSITION: tires may not extend past body more than 1mm per side when viewed from above.

The total wheel width cannot be more than the body of the car plus 1mm. If you run a lot of slop in your axle, we will push the wheel to one side and measure how far past the body the wheel protrudes. This is basically an
issue in the front axle set ups.

Any brand axle spacers or stoppers are allowed

WHEEL SET SCREWS: Any Brand and Hollow setscrews are allowed

REAR WHEEL & TIRES: Any rear wheels and tires may be used, NO FOAM TIRES.

GUIDE FLAG BLADES, BRAID, WIRE and SHIMS:
Any brand guide flags will be allowed. Any brand of braid, wire and shims will be allowed.

MOTOR :
Any Motor may be used without modifying motor mounts.

GEARING:
You can use any type plastic or metal gear or a brass pinion. There is no restriction on the gear combinations (i.e. gear ratios)

Any questions or remarks should be made to Eric or Gary (The Saw).