In

Responded in RSVP 9/12/26 GURNEY/PIERANTONI CUP AT CIRCUIT PETITE LES

IN....

Responded in RSVP 9/12/26 GURNEY/PIERANTONI CUP AT CIRCUIT PETITE LES

Doors open at 4:00, racing at 6:00.

1. CLASSIC F1 ‘50-‘62
2. NC1 CLASSIC
3. MONOGRAM NASCAR
4. MONOGRAM/MRRC SEBRING CHASSIS
5. SCALEY EARLY LEMANS

1. Big Larry
2. Gary
3. Chuck
4. Kevin
5. Mike
6. Randy
7. Jimmy
8. David
9.

Responded in RSVP 9/12/26 GURNEY/PIERANTONI CUP AT CIRCUIT PETITE LES

The Event: RACE WARS
Date: OCTOBER 24th, 2026
Locations: DER SLOTTENHAUSEN 1 RACE
BJM SLOTCARS 1 RACE
BOLINGBROOK SPEEDWAY 2 RACES (tentatively)
The Cars: HYPERCARS

HELIGIBLE CARS:
Scaleauto, Cadillac LMH, BMW Hybrid GTP, Peugeot 9x8 LMH, Porsche P-963 GTP, and Lamborghini. Other hypercars will be allowed as produced.

SLOT.IT CA56 ACURA ARX-05, CA63 Toyota Gr010

Scalextric SCA-C4515, or C4512 Cadillac.

NSR Generic Hypercar

BODY:
Must not be modified or cut in any way

Must be completely painted in a realistic racing livery if not pre-decorated. White kit bodies must have at least a coat of paint on them no naked bodies.

Must start each race with all parts intact except for mirrors, antennas and similar small protruding parts.

Rear wing may be taped or glued in place. Rear wing does not need to be replaced if it comes off durir the race but must be replaced by the next race in the proper position.

Windows must be transparent with the exception of tampo paint or decal headers.

Body screws may be run loose.

ANY brand body to chassis screw is permitted but only in stock location.

Body must have a number (the same number...) in at least three (3) locations.

INTERIORS:
Fully stock, painted

Interior may be modified to allow proper clearance for the motor if necessary.

CHASSIS:
Only stock NSR, Scaleauto, Slot.it, or Scalextric chassis main plates, motor pods are allowed.

Only the stock motor pods are allowed.

Only minor flash removal is allowed on the chassis and motor pod.

No modifications to the axle or bushing mounts are permitted.

Bushings may be glued in place.

The use of tape on the chassis to hold the motor pod in place is approved.

Any Scaleauto or NSR brand motor pod to chassis screws may be used but only in stock locations.

Ballast may be used, ONLY Lead or Tungsten are allowed. Ballast must not offer any support to the chassis or motor pod. Ballast may be placed on the underside of the chassis but care should be used not to contact the track

Any brand axles may be used.

You are allowed to use any combination of glue, tape or screws to secure your motor to the motor pod.

EXCEPTIONS:
Any Brand of Adjustable Front Axle Ride Height screws may be used.

MAGNETIC DOWNFORCE:
No magnets are allowed, you must remove the stock magnet if the car came with one.

WHEELS AND TIRES
FRONT TIRES: Only stock front tires may be used or Quick Slicks Zero grips. Front tires
may be glued and trued (diameter only) with no visual evidence of significant front tire taper allowed. Front tires
may be coated in CA Glue, Nail Polish or Acrylic Floor Wax.

TIRE/WHEEL POSITION: tires may not extend past body more than 1mm per side when viewed from above.

The total wheel width cannot be more than the body of the car plus 1mm. If you run a lot of slop in your axle, we will push the wheel to one side and measure how far past the body the wheel protrudes. This is basically an
issue in the front axle set ups.

Any brand axle spacers or stoppers are allowed

WHEEL SET SCREWS: Any Brand and Hollow setscrews are allowed

REAR WHEEL & TIRES: Any rear wheels and tires may be used, NO FOAM TIRES.

GUIDE FLAG BLADES, BRAID, WIRE and SHIMS:
Any brand guide flags will be allowed. Any brand of braid, wire and shims will be allowed.

MOTOR :
Any Motor may be used without modifying motor mounts.

GEARING:
You can use any type plastic or metal gear or a brass pinion. There is no restriction on the gear combinations (i.e. gear ratios)

Any questions or remarks should be made to Eric or Gary (The Saw).

Responded in RACE WARS 2026 RULES

Practice 8am - Race 10am

Responded in 2026 Finger 500

Working I can’t make it

Responded in 2026 Finger 500

at what time?

Responded in 2026 Finger 500

Can't make it

Responded in 2026 Finger 500

I count 11 going and 2 maybe on FB.

Responded in 2026 Finger 500

just fo ERIC

Responded in 2026 Finger 500

Where's the rules for 2026 finger 500?

Responded in 2026 Finger 500

Big Lare can race👍

Responded in 2026 Finger 500

So far I count 10 with 1 maybe on the Facebook RSVP.

Responded in 2026 Finger 500

I’m a maybe, I should have a def answer by 14th

Responded in 2026 Finger 500

I should be able to make it.

Responded in 2026 Finger 500

So womps have been added to the race card for tomorrow. According to Facebook anyway. Just regular womps.

Responded in RSVP HOTRODS & HANGOVERS 2026 1/1/26

Both classes will be run simultaneously.
You may race either Scaley LMP or GT car or race in both classes.
All cars must meet with box stock with the exception of allowing mandatory lighting requirement for headlights and 1-2 tail lights. If the car has 2 light configuration they must both function.
Race will be approximately three hours long.

Box Stock
use silicone rear tires
true front and rear wheels and tires
add lead
remove front axle slop(up and down and side to side without modifying the chassis)
remove rear axle slop (side to side)(up and down)
change lead wire and braid to mandatory copper.
coat the front tires
glue in the motor
glue in the bushings
change pinion to 9z brass
create chassis rock
you may tape or glue the motor pod to fix or limit travel

If you have any questions or concerns please contact Gary (The Saw).

Responded in 2026 SCALEY NIGHT ENDURO RULES

Sorry I will not make it. We are going out of town.

Responded in RSVP HOTRODS & HANGOVERS 2026 1/1/26

Out

Responded in RSVP HOTRODS & HANGOVERS 2026 1/1/26